PENGARUH UKURAN SERBUK ABU TERBANG BATUBARA TERHADAP LAJU KEAUSAN KOMPOSIT ABU TERBANG BATUBARA / PHENOLIC

MUHAMMAD FATHLIANSYAH P, 1115021055 (2016) PENGARUH UKURAN SERBUK ABU TERBANG BATUBARA TERHADAP LAJU KEAUSAN KOMPOSIT ABU TERBANG BATUBARA / PHENOLIC. FAKULTAS TEKNIK, UNIVERSITAS LAMPUNG.

[img]
Preview
FIle PDF
ABSTRACT (ABSTRAK).pdf

Download (21Kb) | Preview
[img] FIle PDF
SKRIPSI FULL.pdf
Restricted to Hanya pengguna terdaftar

Download (3229Kb)
[img]
Preview
FIle PDF
SKRIPSI TANPA BAB PEMBAHASAN.pdf

Download (3229Kb) | Preview

Abstrak

Kebutuhan akan material kuat, murah, dan ringan semakin meningkat kian waktu, komposit dapat menjadi sebuah solusi akan kebutuhan tersebut dimana bahan penyusun komposit ada yang berasal dari alam dan limbah hasil industri. Pemanfaatan abu terbang batubara juga dapat digunakan dalam pembuatan komposit. Pada penelitian ini dilakukan pembuatan komposit abu terbang batubara/phenolic dengan menggunakan variasi ukuran serbuk pada proses hot pressing. Sehingga dapat diketahui pengaruh variasi ukuran serbuk abu terbang batubara terhadap laju keausan komposit abu terbang batubara/phenolic. Penelitian ini dilakukan dengan variasi serbuk abu terbang batubara 100 mesh, 150 mesh, dan 200 mesh. Komposit abu terbang batubara/phenolic memiliki bahan penyusun dengan komposisi matrik phenolic 60%, sebagai penguat abu terbang batubara, grafit, serbuk besi 20%, barium sulfat 10% sebagai pengisi, dan Nitril Butadiene Rubber 10% sebagai pengikat, diproses dengan metode hot pressing, temperatur pemanasan yang digunakan 250oC, tekanan 60 Mpa, dan temperatur curing 150oC. Ukuran serbuk abu terbang batubara 200 mesh memiliki ketahanan aus terbaik pada penelitian ini, yang membuktikan bahwa ukuran serbuk berpengaruh terhadap sifat mekanik suatu material, kecilnya ukuran serbuk abu terbang batubara inilah yang membuatnya dapat tersebar dan terikat dengan baik pada bahan lain dan mengisi rongga pada komposit. Pada pengujian keausan komposit abu terbang batubara diperoleh nilai spesifik abrasi yang diambil nilai rata-rata, komposit pada ukuran serbuk abu terbang batubara 100 mesh diperoleh hasil spesifik abrasi sebesar 14,589×10-6mm3/mm, pada ukuran serbuk abu terbang batubara 150 mesh diperoleh hasil spesifik abrasi sebesar 19,987×10-6 mm3/mm, pada ukuran serbuk abu terbang batubara 200 mesh diperoleh hasil spesifik abrasi sebesar 12,782×10-6mm3/mm. Kata kunci : Komposit Abu terbang Batubara/Phenolic, Hot Pressing, keausan ABSTRACT The need for strong material, inexpensive, and lightweight growing increasingly time, and the composite can be a solution to these needs, which the constituents of the composite were from natural and industrial wastes. Utilization of coal fly ash can also be used in the manufacture of composites. This research is manufacture of composite coal fly ash/phenolic powder size by using a variation on the process of hot pressing. The effect of variations in the size of powder coal fly ash on composite wear rate of coal fly ash/phenolic can be seen. This research was conducted with the variation of coal fly ash powder of 100 mesh, 150 mesh, and 200 mesh. Composite coal fly ash/phenolic has the constituents of the composition of the matrix of phenolic 60%, as the reinforcement of fly ash coal, graphite, iron powder 20%, barium sulfate 10% as a filler, and nitrile butadiene rubber 10% as a binder, is processed by method of hot pressing, the heating temperature is used to 250oC, a pressure of 60 MPa and temperature of 150oC curing. Powder size of fly ash coal 200 mesh has wear resistance best in this research which proves that the size of the powder affect the mechanical properties of a material. The small size of the powder coal fly ash is what makes it distributed evenly and adherent to the other ingredients. In testing the wear of coal fly ash composite obtained specific values taken abrasion average value, composite powder size of 100 mesh coal fly ash obtained specific results of abrasion of 14,589×10-6mm3/mm, the powder size of 150 mesh coal fly ash obtained specific results of abrasion of 19,987×10-6 mm3/mm, the size of the coal fly ash powder of 200 mesh obtained specific results of abrasion of 12,782×10-6mm3/mm. Keywords: Composite Coal Fly Ash/Phenolic, Hot Pressing, Wearing

Jenis Karya Akhir: Skripsi
Subyek: > Teknik mesin dan mesin
> Teknik mesin dan mesin
Program Studi: Fakultas Teknik > Prodi S1-Teknik Mesin
Pengguna Deposit: 5471184 . Digilib
Date Deposited: 20 Dec 2016 04:03
Terakhir diubah: 20 Dec 2016 04:03
URI: http://digilib.unila.ac.id/id/eprint/24687

Actions (login required)

Lihat Karya Akhir Lihat Karya Akhir