Pengaruh Fraksi Volume Terhadap Kekuatan Tarik Komposit Unidirectional Berpenguat Serat Ijuk Dengan Matriks Epoxy

Agus Kurniawan Mangare, 0715021022 (2015) Pengaruh Fraksi Volume Terhadap Kekuatan Tarik Komposit Unidirectional Berpenguat Serat Ijuk Dengan Matriks Epoxy. Fakultas Teknik, Universitas Lampung.

[img]
Preview
Text
1. ABSTRACT.pdf

Download (82Kb) | Preview
[img]
Preview
Text
2. ABSTRAK.pdf

Download (8Kb) | Preview
[img]
Preview
Text
3. COVER DALEM.pdf

Download (10Kb) | Preview
[img]
Preview
Text
3. LEMBAR PERSETUJUAN.pdf

Download (353Kb) | Preview
[img]
Preview
Text
4. LEMBAR PENGESAHAN.pdf

Download (322Kb) | Preview
[img]
Preview
Text
5. PERNYATAAN.pdf

Download (328Kb) | Preview
[img]
Preview
Text
6. RIWAYAT HIDUP.pdf

Download (72Kb) | Preview
[img]
Preview
Text
7. MOTTO.pdf

Download (22Kb) | Preview
[img]
Preview
Text
8. PERSEMBAHAN.pdf

Download (231Kb) | Preview
[img]
Preview
Text
9. SANWACANA.pdf

Download (156Kb) | Preview
[img]
Preview
Text
11. DAFTAR ISI.pdf

Download (19Kb) | Preview
[img]
Preview
Text
11. DAFTAR GAMBAR.pdf

Download (91Kb) | Preview
[img]
Preview
Text
12. DAFTAR TABEL.pdf

Download (6Kb) | Preview
[img]
Preview
Text
BAB I.PENDAHULUAN.pdf

Download (98Kb) | Preview
[img]
Preview
Text
BAB II.KAJIAN PUSTAKA.pdf

Download (723Kb) | Preview
[img]
Preview
Text
BAB III.METODOLOGI PENELITIAN.pdf

Download (1170Kb) | Preview
[img] Text
BAB IV. HASIL DAN PEMBAHASAN.pdf
Restricted to Registered users only

Download (753Kb)
[img]
Preview
Text
BAB V. SIMPULAN DAN SARAN.pdf

Download (85Kb) | Preview
[img]
Preview
Text
DAFTAR PUSTAKA.pdf

Download (90Kb) | Preview

Abstrak

ABSTRAK Didalam dunia industri kata komposit dalam pengertian bahan komposit berarti penggabungan atau pencampuran antara dua atau lebih bahan yang berbeda kemudian digabung menjadi satu. Komposit tahan terhadap korosi yang tinggi serta memiliki ketahanan yang tinggi pula terhadap beban. Tujuan dari penelitian ini untuk mengetahui pengaruh fraksi volume terhadap kekuatan tarik komposit unidirectional berpenguat serat ijuk dengan matriks epoxy. Pada penelitian ini, serat ijuk yang digunakan adalah serat ijuk serat panjang dan diberi perlakuan alkali NaOH 5% selama 2 jam lalu dikeringkan pada suhu ruangan selama 15 menit. Selanjutnya variasi yang digunakan adalah fraksi volume sebesar 10%, 15%, dan 20%. Proses pembuatan komposit menggunakan metode vacuum dengan perbandingan campuran antara resin epoxy dengan hardener sebesar 1:1 dengan mengacu pada standar ASTM D 638-03. Dari hasil pengujian dan analisa menunjukkan bahwa kekuatan tarik dan regangan tertinggi dicapai pada sampel uji komposit ijuk 20% / epoxy. Nilai kekuatan tarik rata-rata yang didapat sebesar 26,38 MPa dan nilai regangan rata-rata sebesar 8,68 %. Hal ini terjadi karena semakin besar fraksi volume serat ijuk maka semakin besar pula kemampuan komposit dalam menahan beban tarik. Hasil kekuatan tarik komposit unidirectional ijuk / epoxy belum cukup tinggi karena pendistribusian serat yang kurang merata pada proses fabrikasi komposit, serta campuran antara resin dengan hardener yang kurang sempurna. Hasil foto SEM menunjukkan bahwa stuktur ikatan yang terjadi pada komposit C3 lebih baik jika dibandingkan dengan sampel A4. Kata kunci : Komposit unidirectional, Serat ijuk, Uji tarik, Resin epoxy,NaOH, SEM, Metode vacuum. ABSTRACT In the industrial world the terms of said composite material means a merger or mixing between two or more different materials which later merged into one. Composite high corrosion resistant and has a higher resistance to the load. The purpose of this study was to determine the effect of the volume fraction of unidirectional composite tensile strength of fibers with epoxy matrix. In this study, used a long sugar palm fibers and fiber treated with alkali NaOH 5% until 2 hours and then dried at room temperature for 15 minutes. Further variation used is the volume fraction of 10%, 15%, and 20%. Composite manufacturing process using a vacuum with a mixture ratio of epoxy resin and hardener is 1: 1 with reference to the standard ASTM D 638-03. From the test results and analysis indicate that the highest tensile strength and strain achieved in the test sample 20% composite fibers / epoxy. The value of the average tensile strength of 26.38 MPa obtained and the average strain value of 8.68%. That is happens because the larger of volume fraction of sugar palm fiber, then the larger ability of the composite to resist the tensile loads. The results of the tensile strength of unidirectional composite fibers / epoxy is not high enough because of the uneven distribution of fibers in composite fabrication process, as well as a mixture of resin and hardener that is less than perfect. The SEM images showed that the structure of the composite bonding that occurs in C3 is better when compared to samples A4. Keywords: Unidirectional composites, Sugar palm fibers, Tensile test, Epoxy resin, NaOH, SEM, Vacuum method.

Tipe Karya Ilmiah: Skripsi
Subyek: Teknologi > Teknik mesin dan mesin
Teknologi > Teknik mesin dan mesin
Program Studi: Fakultas Teknik > Prodi S1-Teknik Mesin
Depositing User: 9363505 . Digilib
Date Deposited: 17 Mar 2015 06:17
Last Modified: 17 Mar 2015 06:17
URI: http://digilib.unila.ac.id/id/eprint/7687

Actions (login required)

View Item View Item