creators_name: BENNY SILALAHI,  1115021013
creators_id: bangbennymedan@yahoo.com
type: other
datestamp: 2022-05-19 07:20:23
lastmod: 2022-05-19 07:20:23
metadata_visibility: show
title: STUDI PENGUATAN PRESSURE LIMIT PIPA PVC
DENGAN SERAT IJUK
ispublished: pub
subjects: 620
subjects: 720
subjects: TA
full_text_status: restricted
abstract: Pipa merupakan komponen kontruksi yang banyak dipakai industri untuk
penyaluran fluida. Jenis pipa yang banyak dipakai adalah pipa baja. Salah satu
persoalan utama pada pipa adalah korosi. Pada penelitian ini, dikembangakan pipa
PVC berpenguat serat ijuk, sebagai jawaban atas pesoalan tersebut. Pipa PVC
diberi penguat serat ijuk dengan matriks paduan aspal semen dan matriks epoxy.
Untuk matriks paduan aspal semen sudut pelilitan yang digunakan sebesar 550 dan
untuk matriks epoxy sudut pelilitan sebesar 900. Teknik pelilitan menggunakan
Filament Winding Technique (Teknik Pelilitan Serat). Pengujian yang dilakukan
menggunakan Split-Disk Technique (ASTM D2290). Hasil pengujian
menunjukkan pada spesimen pipa berpenguat serat ijuk matriks paduan aspal
semen mengalami penurunan pressure limit (tekanan batas) dan kekuatan tarik
hoop. Pada spesimen pipa berpenguat serat ijuk matriks epoxy, nilai pressure limit
mengalami peningkatan tetapi kekuatan tarik hoop mengalami penurunan.
Penurunan kekuatan tarik hoop ini disebabkan antara lain karena terjadinya
degradasi PVC. Pada spesimen bermatriks paduan aspal semen kekuatan tarik ijuk
tidak teraplikasi karena pemilihan pengujian yang tidak tepat, tidak adanya
perlakuan ijuk sebelum dililitkan, dan proses pelilitan yang kurang tepat.
Kata Kunci : Filament Winding Technique, Split-Disk Technique, limit pressure
(tekanan batas), kekuatan tarik hoop.

ABSTRACT

Pipe is a contruction component that commonly use in industry for fluid
distribution. Steel pipe is the kind of pipe that commonly used in indusrty.
Corrosion is one of the many main pipe problem. In this research, developed PVC
pipe reinforced arenga pinnata merr fiber as an answer for this problem. PVC pipe
was gived reinforced arenga pinnata merr fiber with 2 matrix is combine of
asphalt – cement and epoxy resin. The winding angle of this research that is used
for combine asphalt-cement matrix is 550 and for epoxy resin as matrix used 900.
In this research uses ‘‘filament winding technique’’. The experimental has been
done with split-disk technique (ASTM D2290). The results of experimental shows
decreasing pressure limit and hoop tensile strength of the specimen reinforced
arenga pinnata merr fiber with combine asphalt-cement as matrix. The value of
pressure limit for specimen reinforced arenga pinnata merr fiber with epoxy resin
as matrix increases but the hoop tensille strength decreases. This decreasing of
tensile strength hoop is caused by degradation PVC. This matrix specimen
combined apshalt-cement has tensile strength can’t be applicated because selected
experimental isn’t appropriate, cause there is no behave to arenga pinnata merr
fiber before filament wound, and the process filament wound isn’t appropriate.
Key Word : Filament winding technique, Split-disk technique, pressure limit,
hoop tensile strength.
date: 2016-07-28
date_type: published
publisher: FAKULTAS TEKNIK
place_of_pub: UNIVERSITAS LAMPUNG
citation:   BENNY SILALAHI, 1115021013  (2016) STUDI PENGUATAN PRESSURE LIMIT PIPA PVC DENGAN SERAT IJUK.  FAKULTAS TEKNIK, UNIVERSITAS LAMPUNG.     
document_url: http://digilib.unila.ac.id/23454/1/ABSTRACT%20%28ABSTRAK%29.pdf
document_url: http://digilib.unila.ac.id/23454/2/SKRIPSI%20FULL.pdf
document_url: http://digilib.unila.ac.id/23454/3/SKRIPSI%20TANPA%20BAB%20PEMBAHASAN.pdf